Vapor Barrier / Vapor Diffusion Retarders- Defined
While you are inspecting the attic, check to see if there is a vapor barrier under the attic insulation. The vapor barrier might be tarpaper, Kraft paper attached to fiberglass batts, or a plastic sheet. If there does not appear to be a vapor barrier, you might consider painting the interior ceilings with vapor barrier paint. This reduces the amount of water vapor that can pass through the ceiling. Large amounts of moisture can reduce the effectiveness of insulation and promote structural damage.
Source – Department of Energy:
In most U.S. climates, vapor barriers, or — more accurately — vapor diffusion retarders, should be part of a moisture control strategy for a home. A vapor barrier or vapor diffusion retarder is a material that reduces the rate at which water vapor can move through a material. The older term “vapor barrier” is still used even though “vapor diffusion retarder” is more accurate.
The ability of a material to retard the diffusion of water vapor is measured in units known as “perms” or permeability. The International Residential Code describes three classes of water vapor retarders:
Class I vapor retarders (less than 1 perm):
- Sheet metal
- Polyethylene sheet
- Rubber membrane
Class II vapor retarders (between 1 and 10 perms):
- Unfaced expanded or extruded polystyrene
- 30 pound asphalt coated paper
- Bitumen coated kraft paper
Class III vapor retarders (greater than 10 perms):
- Gypsum board
- Fiberglass insulation (unfaced)
- Cellulose insulation
- Board lumber
- Concrete block
- 15-pound asphalt coated paper
- House wrap
Vapor diffusion retarders can help control moisture in:
- Slab-on-grade foundations
Effective moisture control in these areas and throughout a home must also include air-sealinggaps in the structure, not just the use of a vapor diffusion retarder. How, where, and whether you need a vapor diffusion retarder depends on the climate and the construction of your home.
TYPES OF VAPOR DIFFUSION RETARDERS
Vapor diffusion retarders are typically available as membranes or coatings. Membranes are generally thin, flexible materials, but also include thicker sheet materials sometimes called “structural” vapor diffusion retarders. Materials such as rigid foam insulation, reinforced plastics, aluminum, and stainless steel are relatively resistant to water vapor diffusion. These types of vapor diffusion retarders are usually mechanically fastened and sealed at the joints.
Thinner membrane types come in rolls or as integral parts of building materials. Common examples include polyethylene sheeting and aluminum- or paper-faced fiberglass roll insulation. Another type is foil-backed wallboard. Most paint-like coatings also retard vapor diffusion.
INSTALLING VAPOR DIFFUSION RETARDERS FOR NEW CONSTRUCTION
In mild climates, materials like painted gypsum wallboard and plaster wall coatings may be enough to impede moisture diffusion. In more extreme climates, higher-perm vapor diffusion retarders are advisable for new construction. They perform best when installed closest to the warm side of a structural assembly — toward the interior of the building in cold climates and toward the exterior in hot/wet climates.
A vapor diffusion retarder installation should be continuous and as close to perfect as possible. This is especially important in very cold climates and in hot and humid climates. Be sure to completely seal any tears, openings, or punctures that may occur during construction. Cover all appropriate surfaces or you risk moist air condensing within the cavity, which could lead to dampened insulation. The thermal resistance of wet insulation is dramatically decreased, and prolonged wet conditions will encourage mold and wood rot.
INSTALLING VAPOR DIFFUSION RETARDERS IN EXISTING HOMES
Except for extensive remodeling projects, it’s difficult to add materials like sheet plastic as a vapor diffusion retarder to an existing home. Obtaining an energy audit and thoroughly sealingany leaks it reveals is a very effective strategy for slowing moisture movement in and out of your home.
Your home may not need a more effective vapor diffusion retarder than the numerous layers of paint on its walls and ceilings unless you live in extreme northern climates. “Vapor barrier” paints can be an effective option for existing homes in colder climates. If the perm rating of the paint is not indicated on the label, find the paint formula. The paint formula usually indicates the percent of pigment. To be a good vapor diffusion retarder, it should consist of a relatively high percent of solids and thickness in application. Glossy paints are generally more effective vapor diffusion retarders than flat paints, and acrylic paints are generally better than latex paints. When in doubt, apply more coats of paint. It’s best to use paint labeled as a vapor diffusion retarder and follow the directions for applying it.
COMBINATION AIR BARRIERS/VAPOR DIFFUSION RETARDERS
An air barrier/vapor diffusion retarder attempts to accomplish water vapor diffusion and air movement control with one material. This type of material is most appropriate for southern climates where keeping humid outdoor air from entering the building cavities is critical during the cooling season.
In many cases, air barriers/vapor diffusion retarders consist of one or more of the following materials:
- Polyethylene plastic sheets
- Builder’s foil
- Foam board insulation
- Other exterior sheathings.
Air barriers/vapor diffusion retarders are generally placed around the perimeter of the building just under the exterior finish, or they may actually be the exterior finish. The key to making them work effectively is to permanently and carefully seal all of the seams and penetrations, including around windows, doors, electrical outlets, plumbing stacks, and vent fans.
Missed gaps of any size not only increase energy use, but also increase the risk of moisture damage to the house, especially during the cooling season. An air barrier/vapor diffusion retarder should also be carefully inspected after installation before other work covers it. If small holes are found, you can repair them with caulk or polyethylene or foil tape. Areas with larger holes or tears should be removed and replaced. Patches should always be large enough to cover the damage and overlap any adjacent wood framing.
- Moisture Control
- Air Sealing Your Home
- Air Sealing for New Home Construction
- Types of Insulation
- Insulation and Air Sealing Products and Services
Understanding Vapor Barriers